YUCE, Celalettin ;TUTAR, Mumin ;KARPAT, Fatih ;YAVUZ, Nurettin ;TEKIN, Gökhan . The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 63, n.9, p. 510-518, june 2018. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/>. Date accessed: 19 nov. 2024. doi:http://dx.doi.org/10.5545/sv-jme.2017.4442.
Yuce, C., Tutar, M., Karpat, F., Yavuz, N., & Tekin, G. (2017). The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys. Strojniški vestnik - Journal of Mechanical Engineering, 63(9), 510-518. doi:http://dx.doi.org/10.5545/sv-jme.2017.4442
@article{sv-jmesv-jme.2017.4442,
author = {Celalettin Yuce and Mumin Tutar and Fatih Karpat and Nurettin Yavuz and Gökhan Tekin},
title = {The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {63},
number = {9},
year = {2017},
keywords = {fiber laser welding, aluminum alloys, mechanical characterization; microstructural analysis},
abstract = {The laser welding of aluminium alloys is an important industrial technology but many challenges remain. The objective of this research is to investigate the effect of laser welding parameters on the quality of the fiber laser lap welded AA5182 aluminium alloy. The influences of the laser power, welding speed and focal point position on the mechanical and microhardness properties of the joints were experimentally investigated. The mechanical properties of the joints were evaluated by performing tensile tests. From the experimental results, optimum process parameters were determined, and microstructural examination and microhardness tests were conducted to better understand the performance of the joints. It was found that there is a correlation between the tensile shear loads of the joints and heat input per unit length. At the optimized parameters, the welded joint showed good weld appearance without macro defects, and the joint had an adequate tensile shear load.},
issn = {0039-2480}, pages = {510-518}, doi = {10.5545/sv-jme.2017.4442},
url = {https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/}
}
Yuce, C.,Tutar, M.,Karpat, F.,Yavuz, N.,Tekin, G. 2017 June 63. The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 63:9
%A Yuce, Celalettin %A Tutar, Mumin %A Karpat, Fatih %A Yavuz, Nurettin %A Tekin, Gökhan %D 2017 %T The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys %B 2017 %9 fiber laser welding, aluminum alloys, mechanical characterization; microstructural analysis %! The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys %K fiber laser welding, aluminum alloys, mechanical characterization; microstructural analysis %X The laser welding of aluminium alloys is an important industrial technology but many challenges remain. The objective of this research is to investigate the effect of laser welding parameters on the quality of the fiber laser lap welded AA5182 aluminium alloy. The influences of the laser power, welding speed and focal point position on the mechanical and microhardness properties of the joints were experimentally investigated. The mechanical properties of the joints were evaluated by performing tensile tests. From the experimental results, optimum process parameters were determined, and microstructural examination and microhardness tests were conducted to better understand the performance of the joints. It was found that there is a correlation between the tensile shear loads of the joints and heat input per unit length. At the optimized parameters, the welded joint showed good weld appearance without macro defects, and the joint had an adequate tensile shear load. %U https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/ %0 Journal Article %R 10.5545/sv-jme.2017.4442 %& 510 %P 9 %J Strojniški vestnik - Journal of Mechanical Engineering %V 63 %N 9 %@ 0039-2480 %8 2018-06-27 %7 2018-06-27
Yuce, Celalettin, Mumin Tutar, Fatih Karpat, Nurettin Yavuz, & Gökhan Tekin. "The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys." Strojniški vestnik - Journal of Mechanical Engineering [Online], 63.9 (2017): 510-518. Web. 19 Nov. 2024
TY - JOUR AU - Yuce, Celalettin AU - Tutar, Mumin AU - Karpat, Fatih AU - Yavuz, Nurettin AU - Tekin, Gökhan PY - 2017 TI - The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys JF - Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2017.4442 KW - fiber laser welding, aluminum alloys, mechanical characterization; microstructural analysis N2 - The laser welding of aluminium alloys is an important industrial technology but many challenges remain. The objective of this research is to investigate the effect of laser welding parameters on the quality of the fiber laser lap welded AA5182 aluminium alloy. The influences of the laser power, welding speed and focal point position on the mechanical and microhardness properties of the joints were experimentally investigated. The mechanical properties of the joints were evaluated by performing tensile tests. From the experimental results, optimum process parameters were determined, and microstructural examination and microhardness tests were conducted to better understand the performance of the joints. It was found that there is a correlation between the tensile shear loads of the joints and heat input per unit length. At the optimized parameters, the welded joint showed good weld appearance without macro defects, and the joint had an adequate tensile shear load. UR - https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/
@article{{sv-jme}{sv-jme.2017.4442},
author = {Yuce, C., Tutar, M., Karpat, F., Yavuz, N., Tekin, G.},
title = {The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {63},
number = {9},
year = {2017},
doi = {10.5545/sv-jme.2017.4442},
url = {https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/}
}
TY - JOUR AU - Yuce, Celalettin AU - Tutar, Mumin AU - Karpat, Fatih AU - Yavuz, Nurettin AU - Tekin, Gökhan PY - 2018/06/27 TI - The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 63, No 9 (2017): Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2017.4442 KW - fiber laser welding, aluminum alloys, mechanical characterization, microstructural analysis N2 - The laser welding of aluminium alloys is an important industrial technology but many challenges remain. The objective of this research is to investigate the effect of laser welding parameters on the quality of the fiber laser lap welded AA5182 aluminium alloy. The influences of the laser power, welding speed and focal point position on the mechanical and microhardness properties of the joints were experimentally investigated. The mechanical properties of the joints were evaluated by performing tensile tests. From the experimental results, optimum process parameters were determined, and microstructural examination and microhardness tests were conducted to better understand the performance of the joints. It was found that there is a correlation between the tensile shear loads of the joints and heat input per unit length. At the optimized parameters, the welded joint showed good weld appearance without macro defects, and the joint had an adequate tensile shear load. UR - https://www.sv-jme.eu/sl/article/the-effect-of-process-parameters-on-the-microstructure-and-mechanical-performance-of-fiber-laser-welded-aa5182-aluminium-alloys/
Yuce, Celalettin, Tutar, Mumin, Karpat, Fatih, Yavuz, Nurettin, AND Tekin, Gökhan. "The Effect of Process Parameters on the Microstructure and Mechanical Performance of Fiber Laser-Welded AA5182 Aluminium Alloys" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 63 Number 9 (27 June 2018)
Strojniški vestnik - Journal of Mechanical Engineering 63(2017)9, 510-518
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.
The laser welding of aluminium alloys is an important industrial technology but many challenges remain. The objective of this research is to investigate the effect of laser welding parameters on the quality of the fiber laser lap welded AA5182 aluminium alloy. The influences of the laser power, welding speed and focal point position on the mechanical and microhardness properties of the joints were experimentally investigated. The mechanical properties of the joints were evaluated by performing tensile tests. From the experimental results, optimum process parameters were determined, and microstructural examination and microhardness tests were conducted to better understand the performance of the joints. It was found that there is a correlation between the tensile shear loads of the joints and heat input per unit length. At the optimized parameters, the welded joint showed good weld appearance without macro defects, and the joint had an adequate tensile shear load.