KORKUT, Ihsan ;BOY, Mehmet . Experimental examination of main cutting force and surface roughness dependingon cutting parameters. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 54, n.7-8, p. 531-538, august 2017. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/>. Date accessed: 20 dec. 2024. doi:http://dx.doi.org/.
Korkut, I., & Boy, M. (2008). Experimental examination of main cutting force and surface roughness dependingon cutting parameters. Strojniški vestnik - Journal of Mechanical Engineering, 54(7-8), 531-538. doi:http://dx.doi.org/
@article{.,
author = {Ihsan Korkut and Mehmet Boy},
title = {Experimental examination of main cutting force and surface roughness dependingon cutting parameters},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {54},
number = {7-8},
year = {2008},
keywords = {machining; steel; cutting forces; surface roughness; cutting parameters; },
abstract = {Main cutting forces acting on cutting tool depending on cutting parameters when machining AISI 1117 steel were examined experimentally. Experimental results obtained were compared with the empirical results. For the experimental studies, a Kistler 9257A three component (Fc, Ff and Fp) piezoelectric dynamometer was used to measure cutting forces. This dynamometerwas associated with a 5019 B130 charge amplifier connected to a PC running Kistler Dynoware force measurement software. The empirical results were obtained through Kienzle approach. Five different cutting speeds, five different feed rates and two different depth of cuts were used in the experiments. It was observed that cutting forces decreased as the cutting speed increased and increased by the feed rate. Experimental results also showed similar trends with the empirical results. At the end of experiments, it was observed that surface quality increased by with increasing cutting speed and decreased with increasing feed rate.},
issn = {0039-2480}, pages = {531-538}, doi = {},
url = {https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/}
}
Korkut, I.,Boy, M. 2008 August 54. Experimental examination of main cutting force and surface roughness dependingon cutting parameters. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 54:7-8
%A Korkut, Ihsan %A Boy, Mehmet %D 2008 %T Experimental examination of main cutting force and surface roughness dependingon cutting parameters %B 2008 %9 machining; steel; cutting forces; surface roughness; cutting parameters; %! Experimental examination of main cutting force and surface roughness dependingon cutting parameters %K machining; steel; cutting forces; surface roughness; cutting parameters; %X Main cutting forces acting on cutting tool depending on cutting parameters when machining AISI 1117 steel were examined experimentally. Experimental results obtained were compared with the empirical results. For the experimental studies, a Kistler 9257A three component (Fc, Ff and Fp) piezoelectric dynamometer was used to measure cutting forces. This dynamometerwas associated with a 5019 B130 charge amplifier connected to a PC running Kistler Dynoware force measurement software. The empirical results were obtained through Kienzle approach. Five different cutting speeds, five different feed rates and two different depth of cuts were used in the experiments. It was observed that cutting forces decreased as the cutting speed increased and increased by the feed rate. Experimental results also showed similar trends with the empirical results. At the end of experiments, it was observed that surface quality increased by with increasing cutting speed and decreased with increasing feed rate. %U https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/ %0 Journal Article %R %& 531 %P 8 %J Strojniški vestnik - Journal of Mechanical Engineering %V 54 %N 7-8 %@ 0039-2480 %8 2017-08-21 %7 2017-08-21
Korkut, Ihsan, & Mehmet Boy. "Experimental examination of main cutting force and surface roughness dependingon cutting parameters." Strojniški vestnik - Journal of Mechanical Engineering [Online], 54.7-8 (2008): 531-538. Web. 20 Dec. 2024
TY - JOUR AU - Korkut, Ihsan AU - Boy, Mehmet PY - 2008 TI - Experimental examination of main cutting force and surface roughness dependingon cutting parameters JF - Strojniški vestnik - Journal of Mechanical Engineering DO - KW - machining; steel; cutting forces; surface roughness; cutting parameters; N2 - Main cutting forces acting on cutting tool depending on cutting parameters when machining AISI 1117 steel were examined experimentally. Experimental results obtained were compared with the empirical results. For the experimental studies, a Kistler 9257A three component (Fc, Ff and Fp) piezoelectric dynamometer was used to measure cutting forces. This dynamometerwas associated with a 5019 B130 charge amplifier connected to a PC running Kistler Dynoware force measurement software. The empirical results were obtained through Kienzle approach. Five different cutting speeds, five different feed rates and two different depth of cuts were used in the experiments. It was observed that cutting forces decreased as the cutting speed increased and increased by the feed rate. Experimental results also showed similar trends with the empirical results. At the end of experiments, it was observed that surface quality increased by with increasing cutting speed and decreased with increasing feed rate. UR - https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/
@article{{}{.},
author = {Korkut, I., Boy, M.},
title = {Experimental examination of main cutting force and surface roughness dependingon cutting parameters},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {54},
number = {7-8},
year = {2008},
doi = {},
url = {https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/}
}
TY - JOUR AU - Korkut, Ihsan AU - Boy, Mehmet PY - 2017/08/21 TI - Experimental examination of main cutting force and surface roughness dependingon cutting parameters JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 54, No 7-8 (2008): Strojniški vestnik - Journal of Mechanical Engineering DO - KW - machining, steel, cutting forces, surface roughness, cutting parameters, N2 - Main cutting forces acting on cutting tool depending on cutting parameters when machining AISI 1117 steel were examined experimentally. Experimental results obtained were compared with the empirical results. For the experimental studies, a Kistler 9257A three component (Fc, Ff and Fp) piezoelectric dynamometer was used to measure cutting forces. This dynamometerwas associated with a 5019 B130 charge amplifier connected to a PC running Kistler Dynoware force measurement software. The empirical results were obtained through Kienzle approach. Five different cutting speeds, five different feed rates and two different depth of cuts were used in the experiments. It was observed that cutting forces decreased as the cutting speed increased and increased by the feed rate. Experimental results also showed similar trends with the empirical results. At the end of experiments, it was observed that surface quality increased by with increasing cutting speed and decreased with increasing feed rate. UR - https://www.sv-jme.eu/sl/article/experimental-examination-of-main-cutting-force-and-surface-roughness-dependingon-cutting-parameters/
Korkut, Ihsan, AND Boy, Mehmet. "Experimental examination of main cutting force and surface roughness dependingon cutting parameters" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 54 Number 7-8 (21 August 2017)
Strojniški vestnik - Journal of Mechanical Engineering 54(2008)7-8, 531-538
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.
Main cutting forces acting on cutting tool depending on cutting parameters when machining AISI 1117 steel were examined experimentally. Experimental results obtained were compared with the empirical results. For the experimental studies, a Kistler 9257A three component (Fc, Ff and Fp) piezoelectric dynamometer was used to measure cutting forces. This dynamometerwas associated with a 5019 B130 charge amplifier connected to a PC running Kistler Dynoware force measurement software. The empirical results were obtained through Kienzle approach. Five different cutting speeds, five different feed rates and two different depth of cuts were used in the experiments. It was observed that cutting forces decreased as the cutting speed increased and increased by the feed rate. Experimental results also showed similar trends with the empirical results. At the end of experiments, it was observed that surface quality increased by with increasing cutting speed and decreased with increasing feed rate.