ZAGÓRSKI, Ireneusz . Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry. Articles in Press, [S.l.], v. 0, n.0, p. , june 2024. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/>. Date accessed: 18 jul. 2024. doi:http://dx.doi.org/.
Zagórski, I. (0). Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry. Articles in Press, 0(0), . doi:http://dx.doi.org/
@article{.,
author = {Ireneusz Zagórski},
title = {Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry},
journal = {Articles in Press},
volume = {0},
number = {0},
year = {0},
keywords = {rough milling; 3D surface roughness; Abbott-Firestone curve; rake angle; helix angle; magnesium alloy; },
abstract = {This paper presents the experimental results of a study investigating the impact of machining parameters on 3D surface roughness after rough dry milling. The following 3D roughness parameters were analyzed: Sa, Sq, Sz, Sku, Ssk, Sp, and Sv. Roughness measurements were made on the end face of the specimens. Additionally, 3D surface topography maps and Abbot-Firestone material ratio curves were generated. Carbide end mills with variable rake and helix angles were used in the study. Experiments were conducted on AZ31B magnesium alloy specimens, using a contact-type profilometer. The machining process was conducted using the parameters of so called high speed machining. Three variable technological parameters were analyzed: cutting speed vc, feed per tooth fz, and axial depth of cut ap. The results showed that the surface roughness of the rough milled specimens depended to a great extent on the tool geometry and applied machining parameters. Feed per tooth was found to have the greatest impact on surface roughness parameters. Lower values of the analyzed surface roughness parameters (and therefore higher surface quality) were obtained (in most cases) for the tools with a rake angle γ of 5° and a helix angle λs of 50°. The results provided both theoretical and practical knowledge about the achievable surface roughness after rough milling using tools with different tool blade geometry. It was shown that rough milling is an effective and efficient type of machining for the AZ31B alloy. },
issn = {0039-2480}, pages = {}, doi = {},
url = {https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/}
}
Zagórski, I. 0 June 0. Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry. Articles in Press. [Online] 0:0
%A Zagórski, Ireneusz %D 0 %T Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry %B 0 %9 rough milling; 3D surface roughness; Abbott-Firestone curve; rake angle; helix angle; magnesium alloy; %! Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry %K rough milling; 3D surface roughness; Abbott-Firestone curve; rake angle; helix angle; magnesium alloy; %X This paper presents the experimental results of a study investigating the impact of machining parameters on 3D surface roughness after rough dry milling. The following 3D roughness parameters were analyzed: Sa, Sq, Sz, Sku, Ssk, Sp, and Sv. Roughness measurements were made on the end face of the specimens. Additionally, 3D surface topography maps and Abbot-Firestone material ratio curves were generated. Carbide end mills with variable rake and helix angles were used in the study. Experiments were conducted on AZ31B magnesium alloy specimens, using a contact-type profilometer. The machining process was conducted using the parameters of so called high speed machining. Three variable technological parameters were analyzed: cutting speed vc, feed per tooth fz, and axial depth of cut ap. The results showed that the surface roughness of the rough milled specimens depended to a great extent on the tool geometry and applied machining parameters. Feed per tooth was found to have the greatest impact on surface roughness parameters. Lower values of the analyzed surface roughness parameters (and therefore higher surface quality) were obtained (in most cases) for the tools with a rake angle γ of 5° and a helix angle λs of 50°. The results provided both theoretical and practical knowledge about the achievable surface roughness after rough milling using tools with different tool blade geometry. It was shown that rough milling is an effective and efficient type of machining for the AZ31B alloy. %U https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/ %0 Journal Article %R %& %P 1 %J Articles in Press %V 0 %N 0 %@ 0039-2480 %8 2024-06-16 %7 2024-06-16
Zagórski, Ireneusz. "Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry." Articles in Press [Online], 0.0 (0): . Web. 18 Jul. 2024
TY - JOUR AU - Zagórski, Ireneusz PY - 0 TI - Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry JF - Articles in Press DO - KW - rough milling; 3D surface roughness; Abbott-Firestone curve; rake angle; helix angle; magnesium alloy; N2 - This paper presents the experimental results of a study investigating the impact of machining parameters on 3D surface roughness after rough dry milling. The following 3D roughness parameters were analyzed: Sa, Sq, Sz, Sku, Ssk, Sp, and Sv. Roughness measurements were made on the end face of the specimens. Additionally, 3D surface topography maps and Abbot-Firestone material ratio curves were generated. Carbide end mills with variable rake and helix angles were used in the study. Experiments were conducted on AZ31B magnesium alloy specimens, using a contact-type profilometer. The machining process was conducted using the parameters of so called high speed machining. Three variable technological parameters were analyzed: cutting speed vc, feed per tooth fz, and axial depth of cut ap. The results showed that the surface roughness of the rough milled specimens depended to a great extent on the tool geometry and applied machining parameters. Feed per tooth was found to have the greatest impact on surface roughness parameters. Lower values of the analyzed surface roughness parameters (and therefore higher surface quality) were obtained (in most cases) for the tools with a rake angle γ of 5° and a helix angle λs of 50°. The results provided both theoretical and practical knowledge about the achievable surface roughness after rough milling using tools with different tool blade geometry. It was shown that rough milling is an effective and efficient type of machining for the AZ31B alloy. UR - https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/
@article{{}{.},
author = {Zagórski, I.},
title = {Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry},
journal = {Articles in Press},
volume = {0},
number = {0},
year = {0},
doi = {},
url = {https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/}
}
TY - JOUR AU - Zagórski, Ireneusz PY - 2024/06/16 TI - Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry JF - Articles in Press; Vol 0, No 0 (0): Articles in Press DO - KW - rough milling, 3D surface roughness, Abbott-Firestone curve, rake angle, helix angle, magnesium alloy, N2 - This paper presents the experimental results of a study investigating the impact of machining parameters on 3D surface roughness after rough dry milling. The following 3D roughness parameters were analyzed: Sa, Sq, Sz, Sku, Ssk, Sp, and Sv. Roughness measurements were made on the end face of the specimens. Additionally, 3D surface topography maps and Abbot-Firestone material ratio curves were generated. Carbide end mills with variable rake and helix angles were used in the study. Experiments were conducted on AZ31B magnesium alloy specimens, using a contact-type profilometer. The machining process was conducted using the parameters of so called high speed machining. Three variable technological parameters were analyzed: cutting speed vc, feed per tooth fz, and axial depth of cut ap. The results showed that the surface roughness of the rough milled specimens depended to a great extent on the tool geometry and applied machining parameters. Feed per tooth was found to have the greatest impact on surface roughness parameters. Lower values of the analyzed surface roughness parameters (and therefore higher surface quality) were obtained (in most cases) for the tools with a rake angle γ of 5° and a helix angle λs of 50°. The results provided both theoretical and practical knowledge about the achievable surface roughness after rough milling using tools with different tool blade geometry. It was shown that rough milling is an effective and efficient type of machining for the AZ31B alloy. UR - https://www.sv-jme.eu/sl/article/surface-roughness-evaluation-of-az31b-magnesium-alloy-after-rough-milling-using-tools-with-different-geometry/
Zagórski, Ireneusz"Surface roughness evaluation of AZ31B magnesium alloy after rough milling using tools with different geometry" Articles in Press [Online], Volume 0 Number 0 (16 June 2024)
Articles in Press
This paper presents the experimental results of a study investigating the impact of machining parameters on 3D surface roughness after rough dry milling. The following 3D roughness parameters were analyzed: Sa, Sq, Sz, Sku, Ssk, Sp, and Sv. Roughness measurements were made on the end face of the specimens. Additionally, 3D surface topography maps and Abbot-Firestone material ratio curves were generated. Carbide end mills with variable rake and helix angles were used in the study. Experiments were conducted on AZ31B magnesium alloy specimens, using a contact-type profilometer. The machining process was conducted using the parameters of so called high speed machining. Three variable technological parameters were analyzed: cutting speed vc, feed per tooth fz, and axial depth of cut ap. The results showed that the surface roughness of the rough milled specimens depended to a great extent on the tool geometry and applied machining parameters. Feed per tooth was found to have the greatest impact on surface roughness parameters. Lower values of the analyzed surface roughness parameters (and therefore higher surface quality) were obtained (in most cases) for the tools with a rake angle γ of 5° and a helix angle λs of 50°. The results provided both theoretical and practical knowledge about the achievable surface roughness after rough milling using tools with different tool blade geometry. It was shown that rough milling is an effective and efficient type of machining for the AZ31B alloy.