BOURKAS, George ;SIDERIDIS, Emilios ;YOUNIS, Christos ;PRASSIANAKIS, Ioannis N.;KITOPOULOS, Victor . Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 56, n.10, p. 625-636, october 2017. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/>. Date accessed: 19 nov. 2024. doi:http://dx.doi.org/.
Bourkas, G., Sideridis, E., Younis, C., Prassianakis, I., & Kitopoulos, V. (2010). Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality. Strojniški vestnik - Journal of Mechanical Engineering, 56(10), 625-636. doi:http://dx.doi.org/
@article{., author = {George Bourkas and Emilios Sideridis and Christos Younis and Ioannis N. Prassianakis and Victor Kitopoulos}, title = {Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality}, journal = {Strojniški vestnik - Journal of Mechanical Engineering}, volume = {56}, number = {10}, year = {2010}, keywords = {resin/filler systems; microstructure; fracture strain; perfect adhesion quality; low adhesion quality; }, abstract = {The tensile strength and the fracture strain of particulate composites have been evaluated for the case that adhesion exists between the matrix and filler. Two models, each of three components on the basis of cube-within-cube formation, have been used as representative volume elements. By comparing the derived theoretical results of the strength with experimental data for treated and untreated particles in resin/filler systems, the first model can be characterised as corresponding to perfect adhesion quality between the matrix and filler, while the second one to low adhesion quality. The strength predicted by the first model is close to that of treated particles corresponding to high strength. This model corresponds to an upper bound of the strength in cube-within-cube models. The strength predicted by the second model is close to that of untreated particles corresponding to low strength, but this model does not correspond to a lower bound of strength. The systems used for comparison were resin/glass, resin/iron and resin/SiC particulate composites. For the case that adhesion exists between the matrix and filler, the strengths and fracture strains predicted by the present models are in agreement to those provided by an existing evaluation method in the literature.}, issn = {0039-2480}, pages = {625-636}, doi = {}, url = {https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/} }
Bourkas, G.,Sideridis, E.,Younis, C.,Prassianakis, I.,Kitopoulos, V. 2010 October 56. Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 56:10
%A Bourkas, George %A Sideridis, Emilios %A Younis, Christos %A Prassianakis, Ioannis N. %A Kitopoulos, Victor %D 2010 %T Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality %B 2010 %9 resin/filler systems; microstructure; fracture strain; perfect adhesion quality; low adhesion quality; %! Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality %K resin/filler systems; microstructure; fracture strain; perfect adhesion quality; low adhesion quality; %X The tensile strength and the fracture strain of particulate composites have been evaluated for the case that adhesion exists between the matrix and filler. Two models, each of three components on the basis of cube-within-cube formation, have been used as representative volume elements. By comparing the derived theoretical results of the strength with experimental data for treated and untreated particles in resin/filler systems, the first model can be characterised as corresponding to perfect adhesion quality between the matrix and filler, while the second one to low adhesion quality. The strength predicted by the first model is close to that of treated particles corresponding to high strength. This model corresponds to an upper bound of the strength in cube-within-cube models. The strength predicted by the second model is close to that of untreated particles corresponding to low strength, but this model does not correspond to a lower bound of strength. The systems used for comparison were resin/glass, resin/iron and resin/SiC particulate composites. For the case that adhesion exists between the matrix and filler, the strengths and fracture strains predicted by the present models are in agreement to those provided by an existing evaluation method in the literature. %U https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/ %0 Journal Article %R %& 625 %P 12 %J Strojniški vestnik - Journal of Mechanical Engineering %V 56 %N 10 %@ 0039-2480 %8 2017-10-24 %7 2017-10-24
Bourkas, George, Emilios Sideridis, Christos Younis, Ioannis N. Prassianakis, & Victor Kitopoulos. "Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality." Strojniški vestnik - Journal of Mechanical Engineering [Online], 56.10 (2010): 625-636. Web. 19 Nov. 2024
TY - JOUR AU - Bourkas, George AU - Sideridis, Emilios AU - Younis, Christos AU - Prassianakis, Ioannis N. AU - Kitopoulos, Victor PY - 2010 TI - Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality JF - Strojniški vestnik - Journal of Mechanical Engineering DO - KW - resin/filler systems; microstructure; fracture strain; perfect adhesion quality; low adhesion quality; N2 - The tensile strength and the fracture strain of particulate composites have been evaluated for the case that adhesion exists between the matrix and filler. Two models, each of three components on the basis of cube-within-cube formation, have been used as representative volume elements. By comparing the derived theoretical results of the strength with experimental data for treated and untreated particles in resin/filler systems, the first model can be characterised as corresponding to perfect adhesion quality between the matrix and filler, while the second one to low adhesion quality. The strength predicted by the first model is close to that of treated particles corresponding to high strength. This model corresponds to an upper bound of the strength in cube-within-cube models. The strength predicted by the second model is close to that of untreated particles corresponding to low strength, but this model does not correspond to a lower bound of strength. The systems used for comparison were resin/glass, resin/iron and resin/SiC particulate composites. For the case that adhesion exists between the matrix and filler, the strengths and fracture strains predicted by the present models are in agreement to those provided by an existing evaluation method in the literature. UR - https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/
@article{{}{.}, author = {Bourkas, G., Sideridis, E., Younis, C., Prassianakis, I., Kitopoulos, V.}, title = {Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality}, journal = {Strojniški vestnik - Journal of Mechanical Engineering}, volume = {56}, number = {10}, year = {2010}, doi = {}, url = {https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/} }
TY - JOUR AU - Bourkas, George AU - Sideridis, Emilios AU - Younis, Christos AU - Prassianakis, Ioannis N. AU - Kitopoulos, Victor PY - 2017/10/24 TI - Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 56, No 10 (2010): Strojniški vestnik - Journal of Mechanical Engineering DO - KW - resin/filler systems, microstructure, fracture strain, perfect adhesion quality, low adhesion quality, N2 - The tensile strength and the fracture strain of particulate composites have been evaluated for the case that adhesion exists between the matrix and filler. Two models, each of three components on the basis of cube-within-cube formation, have been used as representative volume elements. By comparing the derived theoretical results of the strength with experimental data for treated and untreated particles in resin/filler systems, the first model can be characterised as corresponding to perfect adhesion quality between the matrix and filler, while the second one to low adhesion quality. The strength predicted by the first model is close to that of treated particles corresponding to high strength. This model corresponds to an upper bound of the strength in cube-within-cube models. The strength predicted by the second model is close to that of untreated particles corresponding to low strength, but this model does not correspond to a lower bound of strength. The systems used for comparison were resin/glass, resin/iron and resin/SiC particulate composites. For the case that adhesion exists between the matrix and filler, the strengths and fracture strains predicted by the present models are in agreement to those provided by an existing evaluation method in the literature. UR - https://www.sv-jme.eu/article/strength-and-fracture-strain-of-resinfiller-systems-using-two-models-1-of-perfect-and-2-of-low-adhesion-quality/
Bourkas, George, Sideridis, Emilios, Younis, Christos, Prassianakis, Ioannis, AND Kitopoulos, Victor. "Strength and Fracture Strain of Resin/filler Systems Using Two Models (1) of Perfect and (2) of Low Adhesion Quality" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 56 Number 10 (24 October 2017)
Strojniški vestnik - Journal of Mechanical Engineering 56(2010)10, 625-636
© The Authors, CC-BY 4.0 Int. Change in copyright policy from 2022, Jan 1st.
The tensile strength and the fracture strain of particulate composites have been evaluated for the case that adhesion exists between the matrix and filler. Two models, each of three components on the basis of cube-within-cube formation, have been used as representative volume elements. By comparing the derived theoretical results of the strength with experimental data for treated and untreated particles in resin/filler systems, the first model can be characterised as corresponding to perfect adhesion quality between the matrix and filler, while the second one to low adhesion quality. The strength predicted by the first model is close to that of treated particles corresponding to high strength. This model corresponds to an upper bound of the strength in cube-within-cube models. The strength predicted by the second model is close to that of untreated particles corresponding to low strength, but this model does not correspond to a lower bound of strength. The systems used for comparison were resin/glass, resin/iron and resin/SiC particulate composites. For the case that adhesion exists between the matrix and filler, the strengths and fracture strains predicted by the present models are in agreement to those provided by an existing evaluation method in the literature.