GOVINDASAMY, Mahadevan ;MANGALAKARAN JOSEPH MANUEL, Lloyd Jenner ;THAMILKOLUNTHU, Senthilkumar . Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis. Strojniški vestnik - Journal of Mechanical Engineering, [S.l.], v. 71, n.1-2, p. 3-9, october 2024. ISSN 0039-2480. Available at: <https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/>. Date accessed: 09 mar. 2025. doi:http://dx.doi.org/10.5545/sv-jme.2024.1084.
Govindasamy, M., Mangalakaran Joseph Manuel, L., & Thamilkolunthu, S. (2025). Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis. Strojniški vestnik - Journal of Mechanical Engineering, 71(1-2), 3-9. doi:http://dx.doi.org/10.5545/sv-jme.2024.1084
@article{sv-jmesv-jme.2024.1084,
author = {Mahadevan Govindasamy and Lloyd Jenner Mangalakaran Joseph Manuel and Senthilkumar Thamilkolunthu},
title = {Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {71},
number = {1-2},
year = {2025},
keywords = {AISI2205; AISI310; corrosion; electrochemical impedance spectroscopy; CaCl2; },
abstract = {The corrosion behavior of dissimilar weldments between AISI310 and AISI2205 stainless steels in a 5 % calcium chloride solution at 50 °C was investigated under three conditions: as-welded, lower post-weld heat treatment at 800 °C, and higher post-weld heat treatment at 1000 °C. Microstructural examination revealed severe pitting in the as-welded sample, with pit widths ranging from 270 μm to 360 μm. The lower heat-treated sample had larger pits (310 μm to 370 μm), while the higher heat-treated sample showed homogeneous corrosion with a protective oxide coating. The as-welded sample had the highest corrosion rate, followed by the lower heat-treated sample, which had a moderate rate, and the higher heat-treated sample had the lowest rate. The corrosion current densities were 5.26×10—³ mA/cm², 4.6×10—4 mA/cm², and 1.4×10—4 mA/cm², respectively. Electrochemical noise measurements confirmed these findings, with the higher heat-treated sample showing negligible localized corrosion and homogenous corrosion behavior.},
issn = {0039-2480}, pages = {3-9}, doi = {10.5545/sv-jme.2024.1084},
url = {https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/}
}
Govindasamy, M.,Mangalakaran Joseph Manuel, L.,Thamilkolunthu, S. 2025 October 71. Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis. Strojniški vestnik - Journal of Mechanical Engineering. [Online] 71:1-2
%A Govindasamy, Mahadevan %A Mangalakaran Joseph Manuel, Lloyd Jenner %A Thamilkolunthu, Senthilkumar %D 2025 %T Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis %B 2025 %9 AISI2205; AISI310; corrosion; electrochemical impedance spectroscopy; CaCl2; %! Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis %K AISI2205; AISI310; corrosion; electrochemical impedance spectroscopy; CaCl2; %X The corrosion behavior of dissimilar weldments between AISI310 and AISI2205 stainless steels in a 5 % calcium chloride solution at 50 °C was investigated under three conditions: as-welded, lower post-weld heat treatment at 800 °C, and higher post-weld heat treatment at 1000 °C. Microstructural examination revealed severe pitting in the as-welded sample, with pit widths ranging from 270 μm to 360 μm. The lower heat-treated sample had larger pits (310 μm to 370 μm), while the higher heat-treated sample showed homogeneous corrosion with a protective oxide coating. The as-welded sample had the highest corrosion rate, followed by the lower heat-treated sample, which had a moderate rate, and the higher heat-treated sample had the lowest rate. The corrosion current densities were 5.26×10—³ mA/cm², 4.6×10—4 mA/cm², and 1.4×10—4 mA/cm², respectively. Electrochemical noise measurements confirmed these findings, with the higher heat-treated sample showing negligible localized corrosion and homogenous corrosion behavior. %U https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/ %0 Journal Article %R 10.5545/sv-jme.2024.1084 %& 3 %P 7 %J Strojniški vestnik - Journal of Mechanical Engineering %V 71 %N 1-2 %@ 0039-2480 %8 2024-10-07 %7 2024-10-07
Govindasamy, Mahadevan, Lloyd Jenner Mangalakaran Joseph Manuel, & Senthilkumar Thamilkolunthu. "Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis." Strojniški vestnik - Journal of Mechanical Engineering [Online], 71.1-2 (2025): 3-9. Web. 09 Mar. 2025
TY - JOUR AU - Govindasamy, Mahadevan AU - Mangalakaran Joseph Manuel, Lloyd Jenner AU - Thamilkolunthu, Senthilkumar PY - 2025 TI - Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis JF - Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2024.1084 KW - AISI2205; AISI310; corrosion; electrochemical impedance spectroscopy; CaCl2; N2 - The corrosion behavior of dissimilar weldments between AISI310 and AISI2205 stainless steels in a 5 % calcium chloride solution at 50 °C was investigated under three conditions: as-welded, lower post-weld heat treatment at 800 °C, and higher post-weld heat treatment at 1000 °C. Microstructural examination revealed severe pitting in the as-welded sample, with pit widths ranging from 270 μm to 360 μm. The lower heat-treated sample had larger pits (310 μm to 370 μm), while the higher heat-treated sample showed homogeneous corrosion with a protective oxide coating. The as-welded sample had the highest corrosion rate, followed by the lower heat-treated sample, which had a moderate rate, and the higher heat-treated sample had the lowest rate. The corrosion current densities were 5.26×10—³ mA/cm², 4.6×10—4 mA/cm², and 1.4×10—4 mA/cm², respectively. Electrochemical noise measurements confirmed these findings, with the higher heat-treated sample showing negligible localized corrosion and homogenous corrosion behavior. UR - https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/
@article{{sv-jme}{sv-jme.2024.1084},
author = {Govindasamy, M., Mangalakaran Joseph Manuel, L., Thamilkolunthu, S.},
title = {Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis},
journal = {Strojniški vestnik - Journal of Mechanical Engineering},
volume = {71},
number = {1-2},
year = {2025},
doi = {10.5545/sv-jme.2024.1084},
url = {https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/}
}
TY - JOUR AU - Govindasamy, Mahadevan AU - Mangalakaran Joseph Manuel, Lloyd Jenner AU - Thamilkolunthu, Senthilkumar PY - 2024/10/07 TI - Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis JF - Strojniški vestnik - Journal of Mechanical Engineering; Vol 71, No 1-2 (2025): Strojniški vestnik - Journal of Mechanical Engineering DO - 10.5545/sv-jme.2024.1084 KW - AISI2205, AISI310, corrosion, electrochemical impedance spectroscopy, CaCl2, N2 - The corrosion behavior of dissimilar weldments between AISI310 and AISI2205 stainless steels in a 5 % calcium chloride solution at 50 °C was investigated under three conditions: as-welded, lower post-weld heat treatment at 800 °C, and higher post-weld heat treatment at 1000 °C. Microstructural examination revealed severe pitting in the as-welded sample, with pit widths ranging from 270 μm to 360 μm. The lower heat-treated sample had larger pits (310 μm to 370 μm), while the higher heat-treated sample showed homogeneous corrosion with a protective oxide coating. The as-welded sample had the highest corrosion rate, followed by the lower heat-treated sample, which had a moderate rate, and the higher heat-treated sample had the lowest rate. The corrosion current densities were 5.26×10—³ mA/cm², 4.6×10—4 mA/cm², and 1.4×10—4 mA/cm², respectively. Electrochemical noise measurements confirmed these findings, with the higher heat-treated sample showing negligible localized corrosion and homogenous corrosion behavior. UR - https://www.sv-jme.eu/article/corrosion-studies-on-post-weld-heat-treated-dissimilar-aisi-2205-and-aisi-310-joints-using-electrochemical-noise-analysis/
Govindasamy, Mahadevan, Mangalakaran Joseph Manuel, Lloyd Jenner, AND Thamilkolunthu, Senthilkumar. "Corrosion Studies on Post-Weld Heat Treated Dissimilar AISI2205 and AISI310 Joints Using Electrochemical Noise Analysis" Strojniški vestnik - Journal of Mechanical Engineering [Online], Volume 71 Number 1-2 (07 October 2024)
Strojniški vestnik - Journal of Mechanical Engineering 71(2025)1-2, 3-9
© The Authors 2025. CC BY 4.0 Int.
The corrosion behavior of dissimilar weldments between AISI310 and AISI2205 stainless steels in a 5 % calcium chloride solution at 50 °C was investigated under three conditions: as-welded, lower post-weld heat treatment at 800 °C, and higher post-weld heat treatment at 1000 °C. Microstructural examination revealed severe pitting in the as-welded sample, with pit widths ranging from 270 μm to 360 μm. The lower heat-treated sample had larger pits (310 μm to 370 μm), while the higher heat-treated sample showed homogeneous corrosion with a protective oxide coating. The as-welded sample had the highest corrosion rate, followed by the lower heat-treated sample, which had a moderate rate, and the higher heat-treated sample had the lowest rate. The corrosion current densities were 5.26×10—³ mA/cm², 4.6×10—4 mA/cm², and 1.4×10—4 mA/cm², respectively. Electrochemical noise measurements confirmed these findings, with the higher heat-treated sample showing negligible localized corrosion and homogenous corrosion behavior.